The GX LTE 4G is a mobile modem for our range of GX surveillance products. It provides mobile internet connection to the system and connection to the VRM portal. It works on 2G, 3G and 4G networks.There are several models. See the guide to see which model best suits the mobile bands available in your area. The GX LTE includes a built-in GPS receiver. If an additional GPS antenna is installed, the system can be tracked as well as geographically delimited by the VRM portal.

The GX Tank 140 takes readings from up to four tank level sensors. It is an accessory for our range of GX system monitoring products, of which the Cerbo GX is the most commonly used model.

Tank levels can be read-out locally in the system, see screenshot, as well remotely through our VRM Portal.

The GX Tank 140 is compatible with current senders (4 to 20 mA) as well as voltage senders (0 to 10 V). The connection to the GX Device is via USB, which is also how the GX Tank is powered: no additional power wires required.

Tank sender wiring is kept as simple as possible: two of the four inputs provide a 24 V power supply, to power the sender. The other two channels do require an external power supply, and there is a power in terminal together with fused outputs to facilitate that.

Upper and lower limits are configurable, to allow using senders that provide only part of the scale, for example 0 to 5 V.

To provide a stable reading, the readings are averaged damping. The damping can be configured between 1 and 60 seconds.

Faulty sensors and wiring issues are detected: an alarm will be raised when values are out of range.

For marine applications, the GX Device can transmit these tank levels on the NMEA 2000 network to be picked up by other displays such as an MFD.

The GX Touch 50 is an accessory for the Cerbo GX display. The five-inch touch screen gives you an instant overview of your system and allows you to adjust settings instantly. Simply connected to the Cerbo GX with a single cable. Their ultra-slim waterproof design, top-mounted setup and easy installation provide a lot of flexibility for an expressive and clean dashboard. Watch the new video explaining everything you need to know about installing the new Cerbo GX and GX Touch 50.

The GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall. No drilling or cut-out is required, other than the three screws that fix the wall mount onto the wall.

This adapter is designed to easily replace the CCGX display with the newer GX Touch. Contents of the packaging are the metal bracket, the plastic bezel, and four mounting screws.

There are two methods of mounting:

“Install including screen” - most secure mounting of the GX Touch display
“Install excluding screen” – GX Touch display is easier to remove, and the adapter can be mounted before completing the wiring
Refer to the Quick Installation Guide for details.

The GX Touch 70 is an accessory for the Cerbo GX display. The five-inch touch screen gives you an instant overview of your system and allows you to adjust settings instantly. Simply connected to the Cerbo GX with a single cable. Their ultra-slim waterproof design, top-mounted setup and easy installation provide a lot of flexibility for an expressive and clean dashboard. Watch the new video explaining everything you need to know about installing the new Cerbo GX and GX Touch 70.

The GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall. No drilling or cut-out is required, other than the three screws that fix the wall mount onto the wall.

The galvanic isolator prevents electrolytic corrosion. It blocks low voltage DC currents that enter your boat via the shore power earth wire. These currents can cause corrosion to the boat’s underwater metals, like the hull, propeller, shaft and so on.
The galvanic isolator consists internally of two diodes which are connected in anti-parallel fashion. When they are connected in this way, the diodes allow current in both directions but only above a certain threshold voltage. The voltage at which diodes conduct is about 1.4 Vdc.

The isolator is installed directly behind your boat's 230V connection. The forward voltage from the galvanic isolator is higher than the potential difference between metals. As a result, this voltage will not allow conduction and as such, the galvanic isolator will prevent any electrolytic current. However, if there is a (higher) error voltage in the AC circuit, the diodes will allow current through and the residual-current device will break the circuit.

The galvanic isolator prevents electrolytic corrosion. It blocks low voltage DC currents that enter your boat via the shore power earth wire. These currents can cause corrosion to the boat’s underwater metals, like the hull, propeller, shaft and so on.
The galvanic isolator consists internally of two diodes which are connected in anti-parallel fashion. When they are connected in this way, the diodes allow current in both directions but only above a certain threshold voltage. The voltage at which diodes conduct is about 1.4 Vdc.

The isolator is installed directly behind your boat's 230V connection. The forward voltage from the galvanic isolator is higher than the potential difference between metals. As a result, this voltage will not allow conduction and as such, the galvanic isolator will prevent any electrolytic current. However, if there is a (higher) error voltage in the AC circuit, the diodes will allow current through and the residual-current device will break the circuit.

The galvanic isolator prevents electrolytic corrosion. It blocks low voltage DC currents that enter your boat via the shore power earth wire. These currents can cause corrosion to the boat’s underwater metals, like the hull, propeller, shaft and so on.
The galvanic isolator consists internally of two diodes which are connected in anti-parallel fashion. When they are connected in this way, the diodes allow current in both directions but only above a certain threshold voltage. The voltage at which diodes conduct is about 1.4 Vdc.

The isolator is installed directly behind your boat's 230V connection. The forward voltage from the galvanic isolator is higher than the potential difference between metals. As a result, this voltage will not allow conduction and as such, the galvanic isolator will prevent any electrolytic current. However, if there is a (higher) error voltage in the AC circuit, the diodes will allow current through and the residual-current device will break the circuit.

This device will bring 4G LTE-M connectivity to all VE.Direct enabled devices without any monthly fees or subscriptions, for the first five years.

DC-AC inverter for powering of 230 V appliances from 48 V supply (for.ex. battery). Input voltage 37,2 - 68 V. Output voltage 230 V / 50 Hz. Output power: max. 3000 VA. Overload and overheating protection. Communication by VE.Direct. Bluetooth is built-in - configure alarms, alarm relay, voltage cut-off, output voltage, frequency, eco-mode and more, all from within VictronConnect.

Victron Energy MK2 interface module to connect PC to Phoenix. For use with v18 software and Phoenix chargers only.

The MK2.2 and MK3 provide a galvanically isolated connection to VE.Bus, and it translates the VE.Bus protocol into the “MK2/MK3 Protocol”

The MK3-USB C allows the following products to connect to a computer for configuration and firmware updates:

Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter / Charger settings in ECOmulti, EasySolar, EasyPlus, and Inverters with a VE.Bus communication port.

DC-AC inverter for powering of 230 V appliances from 48 V supply (for.ex. battery). Input voltage 37,2 - 68 V. Output voltage 230 V / 50 Hz. Output power: max. 5000 VA. Overload and overheating protection. Communication by VE.Direct. Bluetooth is built-in - configure alarms, alarm relay, voltage cut-off, output voltage, frequency, eco-mode and more, all from within VictronConnect.

The MK3-USB allows the following products to connect to a computer for configuration and firmware updates:

Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and Inverters with a VE.Bus communication port.

DC-AC inverter for powering of 230 V appliances from 12 V supply (for.ex. battery). Input voltage 9,2 - 17 V. Output voltage 230 V / 50 Hz. Output power: max. 500 VA. Overload and overheating protection. Communication by VE.Direct.